Clean Still iGo neo Forklift Truck Components for ASSISTANCE Mode

Clean Still iGo neo Components for ASSISTANCE Mode

Preparing the components for cleaning ACAUTION If water penetrates the electrical system, there is a risk of a short circuit occurring!
-Never clean the components used for ASSIS-
TANCE mode using devices such as high-pressure cleaners or rotating brushes.
-While cleaning the rest of the truck, avoid cleaning the components used for ASSISTANCE mode and only clean these components in accordance with the instructions specified below.

STILL STEDS Forklift 8.20 8.18 2020 EPC & Diagnostics Free Download

Risk from damage to electrical components when cleaning!
Only the authorised service centre is permitted to clean the components used for ASSISTANCE mode inside the truck.
-Contact the authorised service centre.
-Park the truck securely.
-Disconnect the battery male connector.
-Contact the authorised service centre to arrange for the components used for ASSIS-
TANCE mode inside the truck to be cleaned. Cleaning the optics covers(S300 safety la-
ser scanner,R2000 laser scanner, foot protection sensors)

 

Cleaning the optics covers(S300 safety laser scanner,R2000 laser scanner, foot pro-
tection sensors)
A CAUTION Abrasive cleaning materials can damage the surfaces of components!
Using abrasive cleaning materials that are unsuitable for plastics can cause plastic parts to dissolve or become brittle. The covers of optical sensors can become cloudy.
-Do not use aggressive cleaning materials (e.g.
acetone, solvents).
-Do not use any abrasive cleaning materials.-Clean the optics covers(inspection windows) on the S300 safety laser scanner, the R2000 laser scanner and the foot protection sensors regularly and in the event of contamination. 

Still Steds Navigator Forklifts 8.20 R2

-A static charge causes dust particles to accumulate on the optics cover. To clean the optics cover, use the antistatic plastic cleaning material listed in the table.

-Remove any dust from the optics covers using a clean, soft brush.
-Moisten the SICK optics cloth with the antistatic plastic cleaning agent. Use the damp cloth to wipe the light output window on the optics covers.
Cleaning other components used for ASSISTANCE mode
-Regularly clean the LED signal lights usinga soft, damp cloth without cleaning agents.
-Clean the remote control using a brush and a damp cloth. Do not use alcohol, solvents or cleaning materials.

How to Remove & Install Fork Carriage for Still Forklift RX20

The process for removing the fork carriage depends on the lift mast type and lift mast design.
The fork carriage can be removed from underneath as the fork wear protection no longer hinders this process; see the chapter entitled "Fork
wear protection".
Still Steds Navigator Forklifts 8.19 R2 Download & Installation Service

 
Removing Still Forklift RX20 Fork Carriage
– Park the truck securely.
– Apply the parking brake.
– Move the lift mast to its vertical position.
– Remove the fork arms.
– If necessary, release the pressure from the hydraulics. See the chapter entitled "Releasing the pressure from the hydraulics".
– If necessary, remove the attachment.
– If necessary, unscrew the hydraulic hoses and support from the fork carriage.
– Tilt the lift mast forwards.
– NiHo and triplex lift masts: Raise the fork carriage until the load chain anchor is easily accessible. Unscrew the locking device for the
load chain on the fork carriage.

– Telescopic lift mast: Raise the lift mast until the load chain anchors are easily accessible.
Unscrew both locking devices for the load chain.
–Move the lift mast to its vertical position.
– Lower the fork carriage and rest it on a europallet.
– Remove the load chains from the guides.
– Slowly raise the inner mast until the support rollers of the fork carriage are no longer guided into the inner mast.


During start-up, ensure that the load chains and hydraulic hoses are not trapped.
– Position the fork carriage on the europallet.

STILL STEDS Forklift 8.19 8.18 2019 EPC & Diagnostics Free Download
Installing Still Forklift RX20 Fork Car
riage
– Position the europallet holding the fork carriage in front of the lift mast.
– Raise the inner mast until the fork carriage fits underneath the inner mast profile.
– Put the fork carriage in an upright position and position it under the inner mast.
– Slowly lower the inner mast until the upper support rollers of the fork carriage are once again engaged in the guides.
– Slowly lower the inner mast completely. When doing this, note the position of the hydraulic hoses and the middle load chain.
– Insert the load chain into the guide on the fork carriage.
– If necessary, raise the fork carriage using the hydraulic jack until the load chain fits into the guide.
– Raise the fork carriage to a comfortable working height.
– Screw in the load chain locking device on the fork carriage.
– Screw the hose line for the attachments to the support on the fork carriage.
– Adjust the play of the support rollers; see the chapter entitled "Support roller play"
– Fit the fork arms.
– Depending on the equipment installed, fit the attachment and auxiliary hydraulics hoses.
– Perform function checking

https://www.autoepccatalog.com