This article show a guide on how to use G-Scan 2 to perform DPF regeneration for Jaguar XF 2011 3L diesel engine.And for more G-Scan 2 test report,please check here:G-Scan 2 Test Projects.
Jaguar EPC Spare Parts Catalogue Download & Installation
Procedures:
Build connection between G-Scan 2 and Jaguar XL by OBD port,then enter menu to select [DIAGNOSIS],then select vehicle model [JAGUAR],model [XF],year [2010-2011]-->[PCM]-->[Diesel]
Then select [Special Function]
Select [Diesel Particulate Filter Dynamic Regeneration]
The function carries out a forced diesel particulate filter dynamic regeneration.
This will only occur if the soot mass present in the filter is below a set upper limit.
The function will determine the soot mass and if it is above the upper limit this function will terminate and you will be instructed to replace the particulate filter.
If it below the upper limit the forced regeneration will be performed.
Be advised that this is a two man operation ad G-scan must remain connected to the vehicle whilst the regeneration is carried out.
Set the ignition switch to ON position (position 2)
To enable the forced dynamin regeneration to function the vehicle must be driven above 40 KPH (2 MPH).The process should take approximately 15 minutes.
The engine operating temperature must be above 60 degrees.
The vehicle must be kept above the required speed for the duration of the procedure.If the speed drops below the required level for 5 minutes or more,the soot mass will stop decreasing and the function must then be re-started.
The vehicle must be driven to the required speed and OKk button must be pressed when this is achieved.
Be advised that this is a two man operation and G-Scan must remain connected to the vehicle whilst the regeneration is carried out.
To enable the forced dynamin regeneration to function the vehicle must be driven above 40 KPH(25 MPH).The process should take approximately 15 minutes.
The vehicle must be driven to the required speed and the OK button must be pressed when this is achieved.
Press OK to continue when ready to start the function.
This procedures will continually read the engine temperature until correct operation condition are met 61℃ or 141.8 ℉.
When the engine temperature up to 61℃,it will show you with below massage:
Active diesel service function
This function will force the engine management system to perform a diesel pariculate filter regeneration.Press [OK] to continue
Active diesel service function
Now active diesel service function is ready
After 30 minutes driven,press OK to continue
This procedure will read the particulate filter soot mass value
This procedure will continually read the particulate filter soot mass value
You now you can the the Soot Mass Value 2.7 g/l
Press [OK]
The soot mass in the particulate filter is now at the acceptable lower limit.
Stop the vehicle safely at the next available opportunity,place in PARK and turn off the ignition .
Press [OK] to continue
Make sure the ignition is switch off
Module initialization
Please wait while the module initializes
Set the ignition switch ON (position 2),then press [OK]
Switch the ignition to off position again
Switch the ignition to ON position again
Forced regeneration completed successfully
From Auto Repair Technician Home, post Jaguar XF 2011 DPF Regeneration by G-Scan 2 Diagnostic Tool
Fendt Vario 700 S4 1001 Crossgate Lever Calibration Guide
This instruction show you guide on how to calibrate 1001 Crossgate Lever for Fendt Vario 700 S4 tractor. Related Contents: FENDT Fendias 2...
-
Here I want to share this guide on how to build WIFI connection for Scania VCI-3 V2.21 .And if you have higher version,the method is same.Ho...
-
Cummins CM850 and CM2850 engine fault code 2311,Electronic Fuel Injection Control Valve Circuit - Condition Exists. Fuel pump actuator circu...
-
It is provided for using this function, that the engine is operating in min-/max governor or allspeed-governor mode (f.e. not fixspeed). Ser...